Raypak Temp-Tracker Specifications download pdf (Page 37)

TempTracker mod+ Hybrid Installation and Operation Manual 37

HTC# 059105-00D



DAY/NIGHTSCHEDULE

SetTime **:**

DaySchedule 6:00a

NightSchedule8:00p

BACK▲▼SAVE

--DAYSCHEDULE--

6:00Am

BACK▲▼SAVE



(Available when "Shutdown or Tstat" is selected from the Shutdown/Tstat/

Setback Startup menu option only)

Button: MENU/<System Settings>/<More Settings>/Day/Night Schedule

• The TempTracker mod+ Hybrid has two levels of heat. The Day (Normal) level is used

when a building is occupied and people are active.

• The Night (Setback) level is used when a building is not occupied, or when people are

sleeping. This setting reduces the calculated temperature by the Setback setting. See

"Setback" on page 33. If the Day calculated water temperature was 150˚F and the Setback

was 20˚F, the Night Schedule will run at (150˚F - 20˚F) = 130˚F.

• If the Boost feature is being used, it uses the Day Schedule as the Boost ending point. See "Boost Mode" on page 26. That

is, if the Day Schedule is set to start at 6:00AM, the Boost will start 30 minutes prior to the Day setting at 5:30AM. The

TempTracker mod+ Hybrid will then raise the calculated water temperature by the Setback amount. Using the previous example,

at 5:30AM the TempTracker mod+ Hybrid will raise the calculated water to 170˚F = (150˚F + 20˚F) until 6:00AM.



Button: MENU/<System Settings>/<More Settings>/Set Time

• Adjust the time by selecting Set Time from the menu and then scrolling through the hours

then select Save. If the hours are to be set to PM, scroll through the AM hours to reach the

PM hours. Then, scroll through the minutes then select Save.

-----SETTIME-----

7:35Pm

BACK▲▼SAVE



Remember that the battery is the backup for the Time. If no power is supplied to the TempTracker mod+ Hybrid

and there was no battery or the battery had no power, time values will be lost and will need to be reset.



Button: MENU/<Maintenance>

The Maintenance menu gives access to sensor and modulating output trimming. In addition,

you'll have access to view the Startup conguration settings.



To be able to change the TempTracker mod+ Hybrid settings the Program/Run

Switch must be set to Program. The switch is located under the Enclosure Wiring

Cover for security. The Enclosure Wiring Cover can be secured using a lock.

-----MAINTENANCE----

SystemTrim +0

OutdoorTrim 0

<OutputTrim>

<Configuration>

BACK▲▼SAVE

SYSTEM

RUNPROGRAM

DO NOT APPLY ANY VOLTAGE

TO INPUT TERMINALS

RS-485

GND

VLT

SYS

PWR

CUR / VLT

GND

VLT

GND

VLT

GND

VLT

TEMP

OUTDOOR

TEMP

SYSTEM

EXTENSION

MODULE

CUR / VLT

PROVE

/DHW

SHUTDOWN

/SETBACK

FOR ALL CIRCUITS

120VAC, 6A RESISTIVE

OUTPUT RATINGS:

1A PILOT DUTY, 15A TOTAL

115VAC 60Hz , 30VA MAX

INPUT RATINGS:

USE COPPER WIRE,

CLASS 1 WIRE ONLY.

CAUTION: RISK OF ELECTRIC SHOCK

More than one disconnect switch may be required

to de-energize the equipment before servicing.

ENCLOSED

ENERGY

MANAGEMENT

EQUIPMENT

99RA

/TSTAT

HYBRID



Adjustablefrom-5F°/-3C°to+5F°/+3C° Default:0°F

Button: MENU/<Maintenance>/System Trim

Button: MENU/<Maintenance>/Outdoor Trim

• The Raypak thermistor type sensors are very accurate, and normally require no calibration.

Sometimes it may be desirable to make small adjustments to the displayed value for either

the Outdoor temperature (OD) or the System temperature (SYS). The Trim setting is used to

adjust the displayed value.

• Do not use the Trim setting to make the Outdoor temperature sensor match that reported on

the radio or TV. Outdoor temperature can vary widely over a broadcast range. Only trim

the outdoor sensor based on an accurate thermometer reading taken where the sensor is

located.

SYSTEMSENSORTRIM

[ ]

BACK▲▼SAVE

OUTDOORSENSORTRIM

[ ]

BACK▲▼SAVE

1 2 ... 32 33 34 35 36 37 38 39 40 41 42 ... 55 56

Comments to this Manuals

No comments

Raypak Temp-Tracker Specifications Page 37

Comments to this Manuals